Because Magboard is structural, non combustible, water resistant, mold resistant, termite resistant strong and impact resistant, Magboard can be used in a variety of indoor and outdoor applications and assemblies. It comes in standard 4x8 and 4x9 sheets with thicknesses ranging from 1/4 to ¾ inch. Magboard can be used as a replacement for: OSB, plywood, cement board, gypsum based sheathing products and drywall in many uses.
Magboard has no silicates. Its basic ingredient, Magnesium Oxide, is a naturally occurring material and is non toxic. Magboard is an inert product qualified for use in hyper-allergenic and clean room applications. Like most construction materials, precaution should be taken for dust when cutting Magboard. Otherwise, Magboard has no special requirements for use.
Magboard can be used in most construction on wood frame, metal frame and SIP panel assemblies. Magboard is installed using methods and tools common to OSB. It can be cut with circular or reciprocating saws. Unlike cement board, it won’t damage blades. In backer board thicknesses, Magboard can be scored and snapped like drywall. On direct to stud applications, Magboard can be attached with, nails, screws, or staples. Magboard’s chemical composition is slightly alkaline and doesn’t affect fasteners, although the use of galvanized materials is recommended. Because Magboard was engineered for strength and fire resistance, it is slightly heavier than drywall although lighter than cement board.
Traditional finishes such as paint, stucco, textures, as well as adhesives work extremely well with MagBoard. Magboard is certified by the National Tile Council for use as a silicate fee backer board using traditional installation methods. Wall preparation for paint or texturing can be done easily with common materials. Magboard’s water, fire and mold resistance can eliminate many of the incremental material and subcontractor cost of protecting existing products so time and cost to finish can be reduced. Installation manual. Need videos here
| Value | MAGBOARD | Cement Board | Plywood | Gypsum Wallboard | Gypsum Shething | O.S.B. |
| Flame Spread | 0 | 0 | High | Low/15 | Low/10 | High |
| Smoke Developed | None | None | High | Low | Low | High |
| Water Resistant | Yes | No | No | No | No | No |
| Mold/Mildew Resistant | Yes | Yes | No | No | No | No |
| Termite Resistant | Yes | Yes | No | Yes | Yes | No |
| Thermal Insulation R-Value per inch | 1.2 | .8 | 1.2 | .9 | 1.1 | 1.0 |
| Impact Strength | High | Medium | High | Low | Low | Medium |
| Weight lbs/sq.ft. | 2.2 | 3.1 | 1.6 | 1.9 | 2.4 | 2.0 |
| Combustibility | Non | Non | Burns | Facing | Facing | Burns |
| Structural | Yes | No | Yes | No | No | Yes |
| Environmental | Good | Good | Good | OK | OK | Poor |
| Freeze/Thaw | Good | Good | Good | Poor | Poor | Good |
| Interior | Tape and Paint | Provide Cladding | Provide Cladding | Tape and Paint | Tape and Paint | Provide Cladding |
| Exterior | Apply Stucco or Cladding | N/A | Apply Paper and Stucco or Cladding | N/A | Apply Stucco or Cladding | Apply Paper and Stucco or Cladding |
| Structurally rated wood and steel frame assemblies | ASTM C 297, C273, C393, C481, E72 |
| Fire rated | Non-combustible Class A ASTM E 136,E 84 |
| Water resistant | ASTM C 666,C 1185-1188,E-96 |
| Mold resistant | ASTM D 3273 rating of 10 |
| Termite resistant | Non nutrient |